Msd 8762 Boost Timing Master for use with MSD Ignition Manuale Utente Scaricare il pdf

IMPORTANT: Read the instructions before attempting installation.

Parts Included:

1 – Boost Timing Master, PN 8762 4 – Self Tapping Screws

1 – Control Knob 1 – 2-Pin Connector

1 – Parts Bag

WARNING: During installation disconnect the battery cables. When disconnecting the battery,

always remove negative cable ﬁrst and install it last.

Note: The PN 8762 must be used with an MSD Ignition Control.

INTRODUCTION

In order to get the most out of your Boost Timing Master, driving tests and ﬁne-tuning are required.

You will want to achieve having the highest advance timing for peak horsepower at low rpm when

boost pressure is low, and retard the timing during boost just enough to prevent knocking or

predetonation.

Note: In setting up the timing curve, a hand held Mighty-Vac or similar tool will allow you to simulate

the boost pressure, while you adjust timing at idle.

PROGRAMMING

Cylinder Select: The Boost Timing Master is programmed

at the factory for 8-cylinder engines. It can easily be

modified for use on 4 and 6-cylinder engines. The

number of cylinders is adjusted by cutting the cylinder

select loops. Figure 1 shows the Cylinder Programming

Loops and how to modify the Unit.

Magnetic Trigger: If you are using a distributor with a

magnetic pickup, such as an MSD, to trigger the ignition

system the White Wire Loop needs to be cut (Figure 1).

If you are using the points or ampliﬁer input of the MSD

Ignition Control, this Loop does not need to be cut.

MOUNTING

The Boost Timing Master can be mounted under the hood, but should be away from direct engine

heat sources. Make sure that the wiring reach their connections. Use the Control as a template to

mark the mounting holes. Remove the unit and drill the holes with an 1/8” drill bit. Use the supplied

screws to mount the unit.

Figure 1 Selecting the Cylinders or Trigger Pickup.

MSD Boost Timing Master

PN 8762

M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4

ONLINE PRODUCT REGISTRATION: Register your MSD product online and you’ll be entered

in our monthly 8.5mm Super Conductor Spark Plug Wire give-away! Registering your product

will help if there is ever a warranty issue with your product and helps the MSD R&D team create

new products that you ask for! Go to www.msdperformance.com/registration.

1 2 3 4

Sommario

Pagina 1 - MSD Boost Timing Master

IMPORTANT: Read the instructions before attempting installation.Parts Included:1 – Boost Timing Master, PN 8762 4 – Self Tapping Screws1 – Cont

Pagina 2 - ADJUSTING THE BOOST

2 INSTALLATION INSTRUCTIONSM S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7

Pagina 3 - INSTALLATION INSTRUCTIONS 3

INSTALLATION INSTRUCTIONS 3M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7

Pagina 4 - Limited Warranty

Limited Warranty MSD warrants this product to be free from defects in material and workmanship under its intended normal use*, when properly installe

Commenti su questo manuale

Nessun commento

Msd 8762 Boost Timing Master for use with MSD Ignition Manuale Utente

Navigare online o scaricare Manuale Utente per Per l'auto Msd 8762 Boost Timing Master for use with MSD Ignition. MSD 8762 Boost Timing Master for use with MSD Ignition Control Installation User Manual Manuale Utente

Sommario

Commenti su questo manuale

Prodotti e manuali riguardandi Per l'auto Msd 8762 Boost Timing Master for use with MSD Ignition